maszyny do napojów używane na sprzedaż (2,105)

Overview This Krones AirCo is an air conveyor for empty PET bottles, built at the end of 2011. The bottles hang by their neck ring and are driven by air from fan units along the conveyor. The installation runs over a total length of approx. 60 m with seven fan units, curves, a diverter and several declining sections. The conveyor sections hang from stainless steel support stands and run at ceiling level across the hall, so the floor beneath stays free for traffic and other machines. Technical data Manufacturer: Krones Model: AirCo Year of manufacture: 2011 Machine type: air conveyor, neck handling of empty PET bottles Total conveyor length: approx. 60 m Declining sections: 10 sections at 10°, approx. 16.8 m in total Curves: 8 with radius 750 mm - 90° 2 x left, 2 x right; 45° left; 30° left; 15° left; 15° right Fan units: 7, each with filter housing Diverter: 1 Conveyor sections In  ...

Overview This GALDI RG50/2 UCS is an automatic form-fill-seal machine for gable-top cartons, built in 2007 in Italy. It erects the cartons from flat blanks, fills and seals them at up to 3,000 cycles per hour, and a cap applicator is included. The machine currently fills liquid egg products and is suitable for milk and other liquid food products. It is still installed and in production. Technical data Manufacturer: GALDI (Italy) Model: RG50/2 UCS Year of manufacture: 2007 Machine type: automatic form-fill-seal machine for gable-top cartons Capacity: up to 3,000 cycles per hour Carton format: 95 x 95 mm cross section Products: liquid egg products; suitable for milk and other liquid foods Installed power: 28 kW Power supply: 380 V / 50 Hz Weight: 5,000 kg Equipment Magazine for flat carton blanks Filling station with sanitary product valves Cap applicator Control panel with QuickPanel View ...

Overview This Scaligera ULISSE 4000 is a sleeve labeling machine for cans, built in 2016 by Scaligera Packaging in Italy. It applies sleeves to sleek and standard cans at up to 4,000 cans per hour and comes with its matching Scaligera steam shrink tunnel from the same year. The line ran carbonated soft drinks in cans and was in production until early September 2023. The machine runs left to right. Sleeves are cut from the reel, opened and placed over the can in the sleever; the steam tunnel then shrinks them tight onto the can body. Technical data Manufacturer: Scaligera Model: ULISSE 4000 Year of manufacture: 2016 Machine type: sleeve labeler with steam shrink tunnel Output: up to 4,000 cans/h Containers: sleek and standard cans Machine direction: left to right Power supply: 400 V, 3-phase, 50 Hz Connected load: 8 kW in total (sleever 2 kW, steam tunnel 6 kW) Max. current: sleever 7 A,  ...

Overview Robotic end-of-line palletizing system from a wine bottling plant, consisting of two ABB FlexPalletizer robot cells, an empty-pallet destacker, a Strapex SWR 30 rotating-ring stretch wrapper with its chain conveyor, and the safety fencing of the installation. The robots stack the packed cases onto pallets fed from the destacker; the loaded pallets run on the chain conveyor through the wrapper. The system is still installed in Belgium and can be viewed by appointment. Technical data Robots: 2 x ABB FlexPalletizer, 4-axis, each with its own ABB robot controller Gripper clearance: 1,200 x 240 mm Pallet size handled by the destacker: 1,100 x 1,200 mm Stretch wrapper: Strapex SWR 30, rotating ring, film width 500 mm, clearance diameter 2,000 mm Wrapper pallet loads: 1/4 EURO, 1/2 EURO, EURO and 1,200 x 1,000 mm, load height up to 2,400 mm Film: pre-stretched LLDPE, pre-stretch levels ...

Producent: Pack und Palettiertechnik Rudolf Steinle Gersthofen GmbH Typ: RAPID-EK Rok produkcji: 1993 Powierzchnia podstawowa skrzynek: 400 mm × 300 mm, odpowiednie dla palet Euronorm 1200 mm × 800 mm Dostępność: od 13.01.2027 Demontaż: przez kupującego Oglądanie: po umówieniu Lokalizacja: Bawaria, Niemcy Ciśnienie powietrza: 6 barów Połączenie: 220/380 V, 50 Hz Sterowanie: 24 V DC

Rozpakowator ARO-P3 firmy Radenska & Steinle (RS) to przemysłowa maszyna do napojów, typowo używana w liniach do rozpakowywania butelek z skrzyń lub skrzyń Stan przedmiotu: W eksploatacji Dostępność: od 13.01.2027 Demontaż: przez kupującego Oglądanie: po umówieniu Lokalizacja: Bawaria, Niemcy Moc: 3 kW Połączenie: 380 V, 50 Hz Ciśnienie powietrza: 6 barów

Radenska & Steinle (RS) SPN-2S to profesjonalna myjka skrzyń, która jest głównie używana w przemyśle napojów do czyszczenia skrzyń zwrotnych po butelkach. Stan przedmiotu: W eksploatacji Dostępność: od 13.01.2027 Demontaż: przez kupującego Oglądanie. Według porozumienia Połączenie: 380 V, 50 Hz Moc: 8 kW Lokalizacja: Bawaria, Niemcy

Typ Schymanski GmbH (MAG): SIRIO 8-24 to przemysłowa pralka do butelek / myjka do butelek, która jest głównie używana w przemyśle napojów do butelek zwrotnych. Stan przedmiotu: W eksploatacji Dostępność: od 13.01.2027 Demontaż: przez kupującego Oglądanie: po umówieniu Lokalizacja: Bawaria, Niemcy Połączenie: 400 V, 50 Hz

Miho DAVID to wysoce innowacyjna maszyna do inspekcji pustych butelek. System ten jest stosowany na całym świecie w branży napojów i spożywczej do płynnego sprawdzania butelek wielokrotnego użytku i jednorazowego użytku (wykonanych ze szkła lub PET) pod kątem wad przed ich ponownym napełnieniem. Dane dotyczące wydajności technicznej: Wysoka przepustowość: System umożliwia pełną kontrolę do 72 000 butelek na godzinę bezpośrednio podczas pracy na linii montażowej. Elastyczność: System nadaje się do obsługi szerokiej gamy kształtów i rozmiarów pojemników. Higieniczne rozwiązanie: Konstrukcja mechaniczna jest zoptymalizowana pod kątem rygorystycznych wymagań higienicznych w zakładach butelkowania i łatwa do czyszczenia. Stan przedmiotu: W eksploatacji Dostępność: od 13.01.2027 Demontaż: przez kupującego Oglądanie: po umów ...

KHS, Krones i Hormes to czołowi producenci i dostawcy systemów i maszyn do butelkowania dla branży napojów i płynów spożywczych. Napełniacz do butelek Producent: KHS Typ: VVF System napełniania butelek KHS, typ VVF (często nazywany Delta VVF lub KHS/SEN VVF), to klasyczny, mechanicznie sterowany system napełniania z ciśnieniem wstecznym, specjalnie opracowany do napełniania napojów zawierających CO2 do butelek szklanych lub PET System zakrętowania butelek Producent: Hormes Typ: KK/SV (połączenie korka koronowego / śrubowej zakręci) Maszyna łączy dwie różne technologie zakrętkowania na bardzo małej przestrzeni. Może elastycznie zamykać butelki (głównie szklane) albo za pomocą korków koronowych (do piwa, lemoniady), albo za pomocą zakrętek (do soków, wina, wody mineralnej). Maszyna do etykietowania obrotowego Producent: Krones Typ:  ...

Radenska & Steinle (RS) ERO-3T to przemysłowy pakowacz butelek (paker / rozpakowywacz) przeznaczony dla branży napojów. Maszyna jest zazwyczaj wykorzystywana w zautomatyzowanych liniach napełniania do zwrotnych butelek szklanych (np. do piwa, wody mineralnej lub napojów gazowanych). Specyfikacja techniczna i szczegóły Typ maszyny: Packer do butelek (Chwytak z głowicą packer) Głowice pakujące: 3 głowice (stąd oznaczenie "3T"), zaprojektowane do równoległego chwytania i przesuwania segmentów butelek (np. siatki pakowania dla standardowych wymiarów skrzynek, np. butelki 6x4 lub 5x4). Ciśnienie robocze: 6 barów ciśnienia powietrza (pneumatyczna kontrola głowic chwytaczy). Stan przedmiotu: W eksploatacji Dostępność: od 13.01.2027 Demontaż: przez kupującego Oglądanie: po umówieniu Lokalizacja: Bawaria, Niemcy Połączenie: 380 V / 50 Hz

Overview This Kematec MBK 12 AS, built in 2006, places shrink capsules on wine bottles and shrinks them on in 12 heating stations. It runs at 3,000 - 12,000 bottles per hour and covers bottle heights of 235 - 360 mm and bottle diameters of 50 - 115 mm. The machine is still installed in a wine bottling line and can be inspected on site. Technical data Manufacturer: Kematec Model: MBK 12 AS Year of manufacture: 2006 Machine type: capsule placing and shrinking machine Output: 3,000 - 12,000 bottles/h Capsules: shrink capsules, max. length 80 mm, max. diameter 40 mm Head diameter: 33 mm Heating stations: 12 Capsule magazine: 1,800 capsules Bottle height: 235 - 360 mm Bottle diameter: 50 - 115 mm Working height: 1,100 mm (+/- 50 mm) Direction of travel: left to right Power supply: 400 V, 50 Hz; main drive 0.75 kW Compressed air: 6 - 7 bar, approx. 350 l/min Overall dimensions (L x W x H): 3,7 ...

Overview KHS Innofill NRF filling and closing monoblock for still wine in glass bottles, built in 2007. A 50-valve filler is followed by two 10-head closers: a KHS natural-cork closer with vacuum device and an aluminium roll-on capper by Zalkin, so the machine closes either corks or screw caps. Output 12,000 bottles per hour. The operator panel and software were updated by KHS in 2022. Technical data Manufacturer: KHS Model: Innofill NRF Year of manufacture: 2007 Output: 12,000 bottles/h Filler: 50 filling valves, pitch circle 1,800 mm, filling tube diameter 20 mm Cork closer: KHS, 10 heads, pitch circle 360 mm, electrically heated cork jaws, cork sorter mounted on top Vacuum device with vacuum pump Screw-cap closer: Zalkin aluminium roll-on capper, 10 heads, pitch circle 360 mm, for 31.4 x 24.2 mm aluminium caps Machine pitch 36π, running direction left to right Conveyor: stainless ste ...

Overview This Logopak LOGOMATIC 920 II PF, built in 2007, is a print-and-apply labelling system for pallets. It prints labels by direct thermal or thermal transfer and applies them with a telescopic tamp applicator onto pallets standing still beside the conveyor. The machine is still installed at the end of a wine bottling and palletising line and can be inspected on site. Technical data Manufacturer: Logopak Model: LOGOMATIC 920 II PF Year of manufacture: 2007 Machine type: print-and-apply pallet labeller Output: 4 labels/min Print methods: direct thermal and thermal transfer Label size: 148 x 210 mm (W x H), 3 mm gap Label roll: max. diameter 400 mm, core diameter 76 mm (150 mm) Mounting: vertical, print head at the bottom Control: Logopak POWER LEAP II Interfaces: W&T COM server, RS 232 Power supply: 88 - 240 V AC, 50/60 Hz; 7 A at 115 V, 3.5 A at 230 V Compressed air: required (valve ...

Overview This Kematec T20-3 KMT, built in 2006, dries filled bottles with air knives on their way through an enclosed tunnel before labelling. The bottles run on a 120 mm plastic chain conveyor under inclined air nozzles on both sides. The machine is still installed in a wine bottling line and can be inspected on site. Technical data Manufacturer: Kematec Model: T20-3 KMT Year of manufacture: 2006 Machine type: bottle dryer (air knife tunnel) Conveyor: plastic chain, 120 mm wide Power supply: 400 V, 3 phases, 50 Hz Control voltage: 24 V DC Overall dimensions (L x W x H): 4,500 x 1,350 x 2,600 mm Equipment Drying tunnel with inclined air knife nozzles above and on both sides of the conveyor, fed by vertical air ducts Infeed screw and curved conveyor sections with adjustable guide rails and quick-release clamping levers Siemens SIMATIC touch panel (French, Dutch, German) with output counte ...

Overview This KHS Innopack CA-1, built in 2006, is a carton erector that forms cartons from flat blanks and closes their bottom with hot-melt glue. Blank stacks are fed on a roller conveyor into the magazine; suction grippers pick each blank, erect it, fold the inner bottom flaps, apply glue with a Robatech hot-melt unit, close and press the outer flaps and discharge the carton onto the outfeed roller conveyor. The machine is still installed in a wine bottling and packaging line and can be inspected on site. Technical data Manufacturer: KHS Model: Innopack CA-1 Year of manufacture: 2006 Machine type: carton erector with bottom gluing Glue system: Robatech Concept hot-melt unit with glue nozzles for the bottom flaps Power supply: 400 V, 3 Ph, 50 Hz, 15 A Compressed air: min. 5 bar operating pressure Overall dimensions (L x W x H): 4,550 x 3,450 x 2,720 mm Blank infeed: roller conveyor wit ...

Overview This KHS Innopack SP, built in 2006, is a pick-and-place case packer for bottles. Empty cases run on the case conveyor into the packing zone, where they are stopped and centred; the gripper head picks the bottle formation from the four-lane infeed table and sets it into the cases. The lifting unit travels on a vertical lifting column with counterweight, and the motion is controlled by a KUKA KR C2 controller with KCP teach pendant. Four change-part trolleys with gripper heads for different bottle sizes are included. The packer is still installed in a wine bottling and packaging line and can be inspected on site. Technical data Manufacturer: KHS Model: Innopack SP Year of manufacture: 2006 Machine type: pick-and-place case packer Bottle infeed: 4 lanes, lane width 85 mm Gripper head: 2 x 18 bottle tulips, formation 3 x 6 bottles Case clearance: 175 x 400 mm Power supply packer: 4 ...

Overview This KHS Innopro warmer-cooler is a skid-mounted thermoregulator for wine, built in 2006 by KHS AG in Dortmund, Germany. It brings wine to a set temperature, heating or cooling as required, at up to 9,900 l/h (99 hl/h), designed for an outlet temperature of 18 °C. The core is a three-section Thermowave plate heat exchanger; stainless steel piping, pumps, pneumatically operated valves and instrumentation are mounted on one frame and run from a freestanding KHS stainless steel control cabinet with touch panel. The unit was last used in a wine bottling line. Technical data Manufacturer: KHS AG (Dortmund, Germany) Model: Innopro warmer-cooler Year of manufacture: 2006 (control cabinet 2007) Machine type: thermoregulator for heating or cooling wine, skid-mounted Product: wine Throughput: 9,900 l/h (99 hl/h) Cooling section: wine from 26 °C to 18 °C, cold water 10 °C to 14 °C at  ...

Overview This KHS Corvus is a skid-mounted cartridge filtration system (microfiltration), built in 2007 by KHS AG in Dortmund, Germany. Four stainless steel KHS cartridge filter housings for 40-inch cartridges are connected through a pneumatically operated valve manifold and controlled from the skids own stainless steel control cabinet with Siemens PLC. The Corvus range is designed for clarifying filtration, cold sterile filtration and safety filtration of wine, beer and water ahead of the filler. This unit was last used for wine filtration in a bottling line. Technical data Manufacturer: KHS AG (Dortmund, Germany) Model: Corvus Year of manufacture: 2007 (filter housings 2006) Machine type: cartridge filtration system (microfiltration), skid-mounted Filter housings: 2 housings for 19 cartridges of 40 inch, 143 L each; 2 housings for 12 cartridges of 40 inch, 108 L each Housing design rat ...

Flow steam generator with 33 kw/h Capacity: 50 kg/h steamStrom / Volt: 400capacity / hour ca.: 50customs no.: 84022000

New Seegräber GmbH TD9 electric steam generator. Manufacturer: Seegräber GmbH, manufacturer article: 100-0001-0900.9.9 kW, steam output 15 kg/h, maximum steam pressure 2.5 bar.3/N/PE 400 V AC, 50 Hz, CEE 5-pole 16 A, fusing 16 A.Water: GeKa coupling, minimum 2.5 bar, steam outlet NW 25.760 × 345 × 690 mm, approx. 50 kg. Cable approx. 5 m.Standard version, accessories quoted separately. Price and delivery time on request.

Overview Tunnel pasteurizer for the continuous thermal treatment of filled cans and bottles by water spray. The tunnel is built in a U-shape: infeed and outfeed sit on the same end of the machine, so the line returns to the operator side and the footprint stays compact at 6.2 m² of working area. The treatment length is divided into eight zones – three heating zones, one pre-pasteurization zone, one pasteurization zone and three cooling zones – with energy recovery between the zones, so heat taken out of the cooling side is fed back into the heating side. Heating is by steam through a plate heat exchanger mounted on the side of the tunnel. Product enters at +10 °C, is held at +70 °C for 10 minutes in the pasteurization zone and leaves at +37 °C; the full cycle takes 41 minutes. Tunnel body and electrical cabinet are built entirely in AISI 304 stainless steel. Control is by Siemens ...

Overview This KOSME FLEXA 15/720 P3 MM is a rotary labelling machine for pre-cut labels, built in 2013. It carries two wet-glue labelling stations, and a third station adds hot-melt labelling, so one machine covers several labelling tasks. It suits bottlers who work with pre-cut labels and need to switch between different labelling jobs. Bottles enter and leave the labelling carousel via infeed and outfeed starwheels, guided through the carousel by container plates and top centring bells. Brush units and side pressing belts in the outfeed area press the labels on. The machine is fully enclosed by transparent safety doors and panels and is operated from a KOSME touch panel that shows machine and production data. The machine is set up with 4 formats, covering containers from 400 to 450 g/ml, and reaches an output of up to 15,000 bottles per hour. Technical data Manufacturer: KOSME Model: F ...

Overview This KOSME DEPACK B B1F A/67-Rf is a depalletizer for empty containers such as blown bottles, built in 2013. It takes containers delivered in several layers on pallets, removes them layer by layer and transfers them to the downstream machine in the line. It handles containers from 100 to 500 ml at up to 13,000 containers per hour. Full pallets run in on pallet chain conveyors, a gantry-type depalletizing head clears the layers and removes the tier sheets. The machine is enclosed by safety fencing with light curtains and access protection. It is controlled by a Siemens PLC from a separate control cabinet outside the machine and operated from a KOSME touch panel. The machine is format-dependent, with several formats set up. Technical data Manufacturer: KOSME Model: DEPACK B B1F A/67-Rf Year of manufacture: 2013 Machine type: depalletizer for empty containers Output: up to 13,000 c ...

System służy do automatycznego czyszczenia pustych zbiorników / pojemników / butelek przed procesem napełniania za pomocą ruchomych dysz powietrza (filtrów czystych). KOSME JET CLEAN G 16/960 1T UP obraca puste pojemniki (nad głową) i usuwa luźne cząstki oraz zanieczyszczenia poprzez wdmuchiwanie filtrowanego powietrza przez ruchome dysze. Maszyna służy do usuwania luźnych osadów z pojemników przed ich wejściem do systemu napełniania. Pojemność: do 6000 butelek/h Wymiary: 2500 x 2500 mm Masa maszyny: 1600 kg Połączenie: 3x400 V, N, 50 Hz Ciśnienie powietrza: 6 barów Ciśnienie wody: 3 bary

Depaletyzator rozdziela palety, wielowarstwowe pojemniki (np. butelki dmuchane / puste butelki) do kontenera transportowego aż do następnej połączonej maszyny. Moc: 13 000 b/h Sterowanie: Siemens Połączenie: 3x400 V, N, 50 Hz Klasa ochrony: IP 54 Moc (elektryczna): 27 kW Obecnie: 49 A Stan zdrowia: dobrze utrzymany, w pełni funkcjonalny Dostępność: od 43. tygodnia 2026

Overview H&K (Holstein und Kappert) SVF 120-D rotary can filler, built in 1991, with 120 filling valves for can format 211/202. Rated output is approx. 80,000 cans per hour with standard 330 ml cans. The filler is supplied together with an Angelus 121 L can seamer from 1991, the rinser that ran with it, and the filler platform. It is controlled by a Siemens S7-400 PLC. The machine is already dismantled and ready for loading. Technical data Manufacturer: H&K (Holstein und Kappert) Model: SVF 120-D Year of manufacture: 1991 Machine type: rotary can filler Filling valves: 120 Can format: 211/202 Output: approx. 80,000 cans/h (330 ml) Power supply: 380 V, 50 Hz, 3/N Rated current: 24 A Control voltage: 24 V DC PLC: Siemens S7-400 (CPU 416-2) Scope of delivery Can filler SVF 120-D with 120 filling valves and can lift cylinders Can seamer: Angelus 121 L (202), year 1991 Can rinser operated tog ...

Overview This SMI SK 452 T is a shrink packer for PET bottles, built in 2002 by SMI (Italy). It collates bottles into pack formations, wraps them in shrink film and shrinks the film in the integrated heating tunnel, at an output of up to 30,000 bottles per hour. It handles 0.5 l, 0.75 l, 1.0 l and 1.5 l bottles in 3x2 packs and 0.5 l bottles in 4x3 packs, and has a pass-through mode for running bottles unpacked. The wrapping section is fully enclosed by safety guarding with viewing windows. The machine has been running as the shrink packer of a PET bottling line for water and is still installed and under power, so it can be inspected in production. Technical data Manufacturer: SMI (Italy) Model: SK 452 T Year of manufacture: 2002 Machine type: shrink packer for PET bottles with integrated heating tunnel Output: up to 30,000 bottles/hour Pack formats: 0.5 l (3x2 and 4x3), 0.75 l (3x2), 1. ...

Overview This Twin Pack handle applicator, built in 2002, applies carry handles to PET bottle multipacks. It comes from a mineral water packaging line of the same year with an output of 20,000 - 30,000 bottles per hour depending on format. The machine is still installed and under power and can be inspected on site. Technical data Manufacturer: Twin Pack Year of manufacture: 2002 Machine type: handle applicator for beverage multipacks Line output: 20,000 - 30,000 bottles/h depending on format Line formats: PET bottles 0.25 l, 0.33 l, 0.5 l, 0.75 l, 1.0 l and 1.5 l Control: Siemens text operator panel Equipment Handle application unit with tape reels on a blue steel frame above the pack conveyor Control panel with separate start, stop and reset for the front and rear sections, emergency stop Guarded enclosure with transparent doors Condition Still installed and under power. An inspection o ...

Cylindroconical 965 hl fermentation and storage tank - designed for cooling with ammonia (can also be cooled with glycol), 1 x cone cooling, 3 x frame cooling - Swivel cone - stainless steel - insulated - Stand frame, short - Cleaning air fitting with safety valve - Vacuum valve 5 tanks, also available individually or in partial quantities., Additional title: Outdoor tanks for storing fluids; years of manufacture 1988 - 1991, Capacity: 96450 l, Operating pressure: 2 bar, Length: approx. 12400 mm, Width: approx. 3950 mm, Height: approx. 3950 mm, Weight: 6220 kg, Material: Stainless steel 1.4301, Position: vertical, Base construction: short supporting skirt, Features: 7 tanks; Cooling: 1 x cone cooling jacket, 3 x side wall cooling jacket; swivel cone; insulation; dearation and cleaning combination; safety valve; vacuum valve; temperature measurement